andreas faucet design, 2018-02-23 16:50:49. To disassemble unscrew and pull off handle. To release the cartridge, use a pair of pliers to pull the retainer clip straight out. Pull out the cartridge and replace the o-rings and seals to fix leaks. You may need to replace the entire cartridge-it is an easy repair that will fix the majority of cartridge faucet leaks. Faucet cartridge come in many styles, so bring the old cartridge to the store. Be sure to insert the new cartridge so it is aligned in the same way as the old cartridge. If the hot and cold are reversed, take the faucet apart and rotate 180 degrees.
derbyan faucet design, 2018-02-09 19:45:35. One of the first things to know before shopping for a faucet is your hole configuration. Most sinks come with holes drilled to receive the faucet and sometimes accessories such as a sprayer, soap dispenser, hot beverage or filtered water faucet. One hole sinks are for single-control faucets, three hole are for single-control faucets with a sprayer and/or accessories and four holes are for single-control or two-handle sinks with various accessories. If you have an under-mount or apron front sink the holes are drilled into the countertop behind the sink.
celindion faucet design, 2018-02-03 19:56:49. Faucets begin to drip when washers, o-rings, or seals inside the faucet are dirty with sediment, covered with mineral deposits, or just worn-out. Fixing a faucet is fairly easy, but varies depending on the type of faucet you have (see below for specific description and instructions). Once you know your faucet design, you can properly disassemble the faucet, locate the source of the leak, and then replace the worn parts or clean dirty parts.
benjamin faucet design, 2018-02-07 19:46:34. Important: After making repairs to a disc faucet, it is imperative the handle in the ON position, then open the shutoff valves slowly. The ceramic discs can be cracked by the sudden release of air from the faucet. Once the water is running steadily, it is safe to close the faucet.
felicia faucet design, 2018-02-08 19:46:05. If you have never held a wrench in your hand, you probably do need a plumber to help you with the installation. But if you know how to connect an end of a pipe to the supply, you can do all the things on your own. Every faucet that is worth your attention will come with detailed instructions. But the process is highly intuitive, too. Basically, the lower part of the faucet comes through the installation hole on your sink or counter-top, hot and cold water pipes connected and the faucet fastened with nuts from beneath.
felicia faucet design, 2018-02-05 19:47:27. It is quite obvious that the touch feature is powered by electricity. Sometimes people ask whether the faucets need to be connected to the mains. They think it might be dangerous. Others mistrust the very idea of electricity and water being together in a faucet. In fact, the touch sensitive faucets are powered by a set of four or six 1.5 V batteries. The voltage reached by such a pack does not exceed 9 volts, which is considered safe voltage even by the strictest regulations. The electricity, however weak, never comes in contact with water. In a typical touch sensitive faucet, water runs inside pipes made from non-conductive materials. So there is no threat whatsoever that could be attributed to the use of electricity in touch sensitive faucets.
derbyan faucet design, 2018-02-04 19:54:16. The cleverly engineered touch sensitivity system distinguishes between "touch" and "grip". When you tap it, your hand needs to be removed from the faucet within a fraction of a second. If the hand stays on the faucet, it is identified as a "grip", and the faucet does not respond. So it is practically impossible for pets to activate it.
andreas faucet design, 2018-02-06 19:47:08. To disassemble unscrew the setscrew and pull off handle. Tighten the plastic adjusting ring inside the cap by turning it with a special flat adjusting tool-or fit tow screwdrivers into the slots and cross their blades to turn the ring. If your ball-style faucet with this type of cap is leaking from the spout, first try tightening the cap with channel pliers. Still leaking? Disassemble and replace worn/broken parts. Often you need to lift out the ball and replace the rubber seats and springs on both sides of the valve. If the faucet leaks around the spout, replace worn o-rings. Replace rotating ball only if clearly worn.