andreas faucet design, 2018-02-23 16:50:49. Before performing this maintenance you should find out if the reason the faucet is leaking is because it was frozen and parts on the inside may be damaged. frost free hose bibs may freeze during freezing temperatures if a hose is left attached to it or if the hose bib is installed with the slope of the hose bib sloping in toward the house. Both conditions prevent the hose bib from draining when it is shut off and then when freezing temperatures happen the hose bib freezes up and is damaged. This article teaches you how to recognize problems with leaky frost free hose bibs and fix them.
benjamin faucet design, 2018-02-21 18:03:35. First - Determine Faucet Design: There are four basic faucet designs: ball-style, cartridge, disc, and compression. Sometimes a faucet type can be determined by the outer appearance, but often the faucet must be taken apart to identify what kind of faucet it is. The four faucet designs come under two categories: washer and washer-less.
andreas faucet design, 2018-02-21 18:02:58. There may be a number of well-grounded reasons for not having touch sensitive faucets in your kitchen. The most widespread one is by far the price that is much higher for touch faucets than for their non-sensitive versions. Some other reasons might be affection for traditional ways, firm determination not to spoil yourself and your family with too effortless ways or plain reluctance to mess with batteries when they need to be changed.
celindion faucet design, 2018-02-21 18:01:27. To disassemble unscrew the setscrew and pull off handle. Tighten the plastic adjusting ring inside the cap by turning it with a special flat adjusting tool-or fit tow screwdrivers into the slots and cross their blades to turn the ring. If your ball-style faucet with this type of cap is leaking from the spout, first try tightening the cap with channel pliers. Still leaking? Disassemble and replace worn/broken parts. Often you need to lift out the ball and replace the rubber seats and springs on both sides of the valve. If the faucet leaks around the spout, replace worn o-rings. Replace rotating ball only if clearly worn.
derbyan faucet design, 2018-02-21 18:03:17. Pullout faucets have a spray head that pulls out towards you, whereas a pull-down faucet has a spray head that pulls down toward the bottom of the sink. Both options help you clean the sink and wash produce or water plants. The pull-outs are the fastest growing in popularity of any faucet in the industry with good reason, they are the perfect combination of style and function. A button or toggle control makes it easy to go from aerated stream to spray. Look for one that swivels 360 degrees for easy access to all areas of your sink.
felicia faucet design, 2018-02-21 19:10:59. It is quite obvious that the touch feature is powered by electricity. Sometimes people ask whether the faucets need to be connected to the mains. They think it might be dangerous. Others mistrust the very idea of electricity and water being together in a faucet. In fact, the touch sensitive faucets are powered by a set of four or six 1.5 V batteries. The voltage reached by such a pack does not exceed 9 volts, which is considered safe voltage even by the strictest regulations. The electricity, however weak, never comes in contact with water. In a typical touch sensitive faucet, water runs inside pipes made from non-conductive materials. So there is no threat whatsoever that could be attributed to the use of electricity in touch sensitive faucets.
derbyan faucet design, 2018-02-21 18:01:42. There may be a number of well-grounded reasons for not having touch sensitive faucets in your kitchen. The most widespread one is by far the price that is much higher for touch faucets than for their non-sensitive versions. Some other reasons might be affection for traditional ways, firm determination not to spoil yourself and your family with too effortless ways or plain reluctance to mess with batteries when they need to be changed.
benjamin faucet design, 2018-02-21 18:02:21. To disassemble unscrew the bonnet from the faucet, using slip-joint pliers. Remove the valve stem, keeping in mind this has reverse threads, so unscrew it by turning it clockwise. Older compression faucets may have corroded handles that can be difficult to remove. Most hardware stores and rental centers have a specialty tool called a Handle Puller which makes the job easier.