derbyan faucet design, 2018-02-23 16:50:11. Cartridge Faucet - this washerless faucet is identified by the narrow metal or plastic cartridge inside the faucet body; and it is available in both single and double handled cartridge designs. Cartridge faucets have a hollow cartridge insert that lifts and rotates to control the flow and temperature of water. Dripping at the spout occurs when the cartridge seals wear out. Leaks at the base are caused by worn o-rings.
derbyan faucet design, 2018-02-22 19:45:45. To disassemble unscrew the setscrew and pull off handle. Though these faucets are washerless, they do have inlet and outlet seals that may leak, or sediment may build up inside the inlets and cause leaks. After removing the escutcheon cap, lift out the cylinder and clean the neoprene seals and cylinder openings. Be sure the faucet is in the "open" position when replacing seals.
andreas faucet design, 2018-02-22 19:45:19. To disassemble unscrew the setscrew and pull off handle. Tighten the plastic adjusting ring inside the cap by turning it with a special flat adjusting tool-or fit tow screwdrivers into the slots and cross their blades to turn the ring. If your ball-style faucet with this type of cap is leaking from the spout, first try tightening the cap with channel pliers. Still leaking? Disassemble and replace worn/broken parts. Often you need to lift out the ball and replace the rubber seats and springs on both sides of the valve. If the faucet leaks around the spout, replace worn o-rings. Replace rotating ball only if clearly worn.
felicia faucet design, 2018-02-22 22:09:05. If you have never held a wrench in your hand, you probably do need a plumber to help you with the installation. But if you know how to connect an end of a pipe to the supply, you can do all the things on your own. Every faucet that is worth your attention will come with detailed instructions. But the process is highly intuitive, too. Basically, the lower part of the faucet comes through the installation hole on your sink or counter-top, hot and cold water pipes connected and the faucet fastened with nuts from beneath.
celindion faucet design, 2018-02-22 19:46:09. First - Determine Faucet Design: There are four basic faucet designs: ball-style, cartridge, disc, and compression. Sometimes a faucet type can be determined by the outer appearance, but often the faucet must be taken apart to identify what kind of faucet it is. The four faucet designs come under two categories: washer and washer-less.
felicia faucet design, 2018-02-22 19:44:35. A small drip from a leaky faucet might seem like a little annoyance, yet it actually can cost you hundreds of dollars a year in water down the drain and next to nothing to fix. A leaky faucet is one of the most common home plumbing problems. Faucets are relatively easy to fix-once you know how they work and what to do to fix them.
felicia faucet design, 2018-02-22 22:09:26. To disassemble unscrew the bonnet from the faucet, using slip-joint pliers. Remove the valve stem, keeping in mind this has reverse threads, so unscrew it by turning it clockwise. Older compression faucets may have corroded handles that can be difficult to remove. Most hardware stores and rental centers have a specialty tool called a Handle Puller which makes the job easier.
andreas faucet design, 2018-02-22 22:08:58. To disassemble unscrew the setscrew and pull off handle. Though these faucets are washerless, they do have inlet and outlet seals that may leak, or sediment may build up inside the inlets and cause leaks. After removing the escutcheon cap, lift out the cylinder and clean the neoprene seals and cylinder openings. Be sure the faucet is in the "open" position when replacing seals.